If you are ready to design the layout of your alarm system are, for the installation, you must decide where to mount the alarm center. If you have a basement unfinished, will drill down and run the wires in the rafters of the area you want for the panel. In most cases, this will be the mechanical room or boiler.
If you work in a one-story building, will run your wires up to the attic and unfinished
Drop the cord to theto control.
If you are in a commercial application, it will run the cables on top of the ceiling or along the beams or may be subjected by conduction.
If you're in a place where there is no place to run all those wires and hide them, then a candidate for a wireless system.
We want to make sure that wherever you installed the alarm system that you choose a device like a motion detector or door contact, to protect it. Leave the panel in aunprotected area could easily in case of a break given to bypass the wires running through the basement, and when they jump on a mobile in the protected area of the house. If you are wondering, "what is not on the exposed wires in the basement?". Cut the wire twice to open the device that would be executed, and would cause an alarm if the system was armed.
If you go to vote on the wireless system of your choice, choose a centralPosition in the home or office, that a strong radio signal received from all points of protection. Remember that even with the wireless system, there are some wires that must be performed. In most cases they are the keyboard, the siren, the AC adapter and phone cord. Take this into account when choosing the location running.
Enter the selected area lighting, as this will be where you work because most of your installation. Put a towel and put all the products andTools and a trash bag in this area. I have learned over the years to come to get my location, what I need and return everything that I did not return to this place when I'm done with them, especially tools. If you do not perform an installation organized, you're half your time looking for a tool that spend part of the coil of wire, etc. A belt tool is useful for tools you need anywhere, as the drill fresh tape, diameter wire, screwdriver, compound B, a small bubbleLevel, stud finder, a clean, etc.
You want to clean as you go. As with any wire fabrication and installation of facilities that will take the time to clean up all waste and bring the bag to your area of control. The anal is a good thing if you run a quality installation.
As each wire in the control room to run, so far as the wire is coming into the panel hole, and add about a foot of wire before cutting diagonally with yourCutter. Place a piece of luminous tape around the wire about 5 inches from the end and write on the tape with a permanent marker Sharpie or where it goes.
If your home or office is under construction, you can choose to pre-wire for security. Pre-wiring is an advantage in the ability of each device in the exact position you want to get it. Place wires and boxes, the device is completed before the building depends on your ability to read drawings andunderstand where cabinets, appliances and electrical devices to be placed with precision. If you pre-wire to be sure to choose their own holes in the wall studs and rafters to drill. Many lazy alarm technician will walk through the electrical and plumbing holes and think they are getting the easy way. The problem is that if an electrician or plumber no inspection need to pull cables and pipes in order to move the special inspector. There are likely to be affectedon the wire, if they do.
The best time to keep the cables of a string of pre-design will begin immediately after the electrician and get in front of insulators.
If you are willing to run the cables begin, start with the front door. If you are down in the cellar, you will work through the low door opening. If you have your veins until the work on top of the door. Allows you to use for our example. What kind of contact will be with you? Box surface mountor expanded? If you wire in any case, why not take the time to install the contacts built, so that they are from the site when the door is closed? Set the drill with a 3/8-inch standard length drills.
In the jam of the door, starting at about 4 cm from the bottom holes at an angle toward the basement. Switch to your thumb tip 3/8- 12 to 18 cm long and continue drilling to the basement, finally, the 5-foot-long bell hanger bits and passcontinue drilling until they pop into the cellar. Pull out the long piece from the hole and remove it from the hole. Poke the end of the bit in the long, narrow hole.
Go to the basement with a flashlight, wire cutters diagonal ribbons, markers, stapler with stitches in it, and a package of reel or 22-gauge 2-conductor wire. Strip the plastic over the end of the wire about 2 cm. Turn the 2 wires together and thread through the hole at the end of the lean side of the little 'longand turn on themselves. Back to the top and pull the wire up the hole. A large knot in the line loose and temporary after that to get there, so as not to fall into the hole. Allow at least 12 cm above so that you can work with the wire.
Jump to restore start at the bottom, and the wire enough for your control panel to do. The wire staple gun with a basic industry as a T22 along the beam in a clean and tidy from the drop-hole at the direction of the controlPanel. Make sure to penetrate, not flush with each clip, if you remove, do so now and re-stitching. These errors are hard to track after walking. Be sure to make the pin on the back wall where the control panel (about chest height) and can affect one foot or more additional wire from the coil before cutting. Mark the thread to the inch tape and markers other than the end.
Congratulations! You have your first race. Be sure to pick up and returnall the tools to the starting point so you know where they are when you need it.
Take your contact 3 / 8 inches and built-in magnet. Need An Extension drill (if you use a cordless drill), duct tape and a cutter. Divide the end of your wire and strip a small amount of plastic cover from each end. Do the same for your contact if you have the kind of small screws for the wires that stuck. Twist each end of the wire at one end of theContact wire and narrow strip and individually. After all, you can use a piece of tape to wrap around the entire set. (It does not matter which wire goes to the line, as this is a wire loop, and has no positive or negative side). Carefully hit the wire into the hole and push the contact in the door now mark the point of contact with the magnet when the door is closed. Stabilize the door and drill a 3 / 8 "hole just deep enough to put the magnet on the repetitionEvery port you wish to contact. We always recommend that you contact each perimeter of the door.
We are writing to find out additional hardware for cabling experts! Alarms Web site to access it.
You again soon! because we are adding do-it-yourself installation techniques are often plants.
0 comments:
Post a Comment